Original Factory Technical Manual for the John Deere 1032, 1042, 1052, 1055 Combines.
This manual is very detailed and contains all the official John Deere manufacturer specifications, troubleshooting, repair instructions step by step with illustrations and wiring diagrams. Simple to complicated repairs can be completed effortlessly with the information provided. It is 100 percent complete and intact. The manual is specifically written for the DIY as well as the experienced mechanic.
Models Covered:
John Deere 1032 Combine
John Deere 1042 Combine
John Deere 1052 Combine
John Deere 1055 Combine
CONTENTS AS FOLLOWS:
SECTION 10 – GENERAL
Group 05 – Specifications
Group 10 – Testing and adjustments
SECTION 20 – ENIGNE REPAIR
Group 05 – Removal and installation, 4-cyl. engine
Group 10 – Removal and installation, 6-cyl. engine
SECTION 30 – FUEL AND AIR SYSTEM REPAIR
Group 05 – Fuel filter with water trap nd electrical fuel transfer pump
SECTION 40 – ELECTRICAL SYSTEM REPAIR
Group 05 – Wiring harnesses and connectors
Group 10 – Starting motor (to Serial No. 049283)
Group 11 – Starting motor (from Serial No. 049284)
Group 15 – Alternator (65 A)
Group 16 – Alternator (95 A)
Group 20 – System components
Group 25 – Low shaft speed monitor system
Group 30 – Electromagnetic transmission brake
SECTION 50 – POWER TRAIN
Group 05 – Variable ground speed drive
Group 10 – Engine clutch and mechanical clutch operation (3-speed transmission)
Group 11 – Engine clutch and hydraulic clutch operation (3-speed transmission)
Group 15 – Engine clutch operation (4-speed transmission)
Group 16 – Clutch operation system (4-speed transmission, from Serial No. 049593)
Group 20 – Engine clutch (4-speed transmission)
Group 21 – Engine clutch (4-speed transmission, from Serial No. 044137)
Group 25 – Three-speed transmission
Group 30 – Four-speed transmission
Group 35 – Final drives, differential (3-speed transmission)
Group 40 – Final drives, differential (4-speed transmission)
Group 45 – Final drive on rice combine (4-speed transmission)
Group 50 – Track system
SECTION 60 – BRAKES, REAR AXLE AND STEERING
Group 05 – Parking brake (3-speed transmission)
Group 10 – Parking brake (4-speed transmission)
Group 15 – Brake operation
Group 20 – Foot brakes (3-speed transmission)
Group 25 – Foot brakes (4-speed transmission)
Group 26 – Foot brakes with integrated slave cylinder (rice combine)
Group 30 – Rear axle
Group 35 – V-support for wide rear axle
Group 40 – Hydrostatic steering unit
Group 45 – Steering cylinder
SECTION 70 – HYDRAULIC SYSTEM REPAIR
Group 05 – Hydraulic oil reservoir and lines
Group 10 – Hydraulic pump
Group 15 – 3- and 4-spool control valves with flow divider
Group 20 – Hydraulic cylinders
Group 25 – Nitrogen accumulators
SECTION 80 – MISCELLANEOUS
Group 05 – Bearings and shafts
Group 10 – Drive belts
Group 15 – Drive chains
SECTION 90 – OPERATOR’S PLATFORM WITH CAB
Group 05 – Cab ventilation system
Group 10 – Safe handling of refrigerants
Group 15 – Air conditioning compressor
Group 20 – Air conditioning system service and tests
Group 25 – Air conditioning system components
Group 30 – Cab heating system
Group 35 – Operator’s seat
Group 40 – Operator’s cab
Group 45 – Platform control levers
SECTION 100 – CUTTING PLATFORM AND CORN HEAD
Group 05 – Cutting platform and knife drive
Group 10 – Cutting platform auger
Group 15 – Variable reel speed drive
Group 20 – Corn head
Group 25 – Corn head gear case
SECTION 110 – FEEDER HOUSE
Group 05 – Feeder drive
Group 10 – Feeder with integrated platform
Group 15 – Feeder with quick-tach platform
SECTION 120 – SEPARATOR AND CLEANING UNIT
Group 04 – Stone trap
Group 05 – Separator drive
Group 10 – Variable cylinder drive
Group 15 – Threshing cylinder
Group 20 – Concave
Group 25 – Beater variable drive
Group 30 – Beater
Group 35 – Cross shaker
Group 40 – Straw walkers
Group 45 – Cleaning shoe and sleves
Group 50 – Fan and variable fan drive
SECTION 130 – GRAIN PROCESSING
Group 05 – Clean grain and tailings augers
Group 10 – Clean grain elevator
Group 15 – Tailings elevator
Group 20 – Upper tailings auger
Group 25 – Grain tank leveling auger
Group 30 – Grain tank center fill auger
Group 35 – Inner grain tank unloading auger
Group 40 – Riser tube
Group 45 – Discharge tube
SECTION 140 – SPECIAL EQUIPMENT
Group 05 – Straw chopper drive
Group 06 – Straw chopper direct drive
Group 10 – Straw chopper rotor bearings
SECTION 230 – FUEL SYSTEM – OPERATION AND TESTS
Group 05 – Fuel filter with water trap and electrical fuel transfer pump
SECTION 240 – ELECTRICAL SYSTEM – OPERATION AND TESTS
Group 05 – Electrical circuit and wiring diagrams
Group 06 – Circuit testing
Group 10 – Starting motor
Group 15 – Alternator
SECTION 250 – POWER TRAIN – OPERATION AND TESTS
Group 05 – Clutch and mechanical clutch operation (3-speed transmission)
Group 06 – Clutch and hydraulic clutch operation (3-speed transmission)
Group 10 – Clutch operation (4-speed transmission)
Group 15 – Clutch (4-speed transmission)
Group 20 – Three speed transmission
Group 25 – Four-speed transmission
SECTION 260 – BRAKES, REAR AXLE AND STEERING – OPERATION AND TESTS
Group 05 – Brake Operation
Group 06 – Foot brakes and brake operation (rice combine)
Group 10 – Primary (steering) circuit – General information and circuit diagram
Group 15 – Primary (steering) circuit – Diagnosing malfunctions
Group 20 – Primary (steering) system – Testing
SECTION 270 – HYDRAULIC SYSTEM – OPERATION AND TESTS
Group 05 – Hydraulic circuit symbols
Group 10 – Secondary (lift) circuit – General informaion and circuit diagram
Group 15 – Secondary (lift0 circuit – Diagnosing malfunctions
Group 20 – Secondary (lift) circuit – Testing
SECTION 290 – OPERATOR’S PLATFORM WITH CAB – OPERATION AND TESTS
Group 05 – Cab ventilation system
Group 10 – Air conditioning system
Group 15 – Safe handling of refrigerants
Group 20 – Air conditioning system service and tests
Group 25 – Cab heating system
———————-
Model Specification: John Deere 1032, 1042, 1052, 1055 Combines
Publication number: TM4413
Language: English
Total Pages: 731
File Format: PDF
Requirements: Adobe PDF Reader
Zoom In/Out: yes
Notes: Bookmarked, searchable, Fully printable, instant download
Compatible: All Versions of Windows & Mac, Linux OS, Iphone, Ipad, Smartphone, Android etc…
———————-
Pay Today and Download the complete manual instantly. The download link will also be sent to your e-mail. So please make sure your email address is correct. Don’t Forget to Check Spam / Junk if can’t find the new message in your email inbox immediately.
Thanks for Visiting.